宣汉——达县地区飞仙关组储层预测方法研究

在宣汉-达县地区,以往仅依据地震属性来预测飞仙关组储层分布,钻探结果与实际情况不符,为此本文提出量化分析预测结合主参数分析的新方法和新思路。在量化分析中首先对飞仙关组储层进行高分辨率反演,获得储能系数图;然后结合主振幅剖面和主频率剖面分析,对储层进行预测。在研究区,本方法的预测结果与实钻情况相吻合。     

高炉鼓风机电气控制技术改造

对高炉鼓风机事故原因分析发现，低电压保护动作、二次控制电源断电、电网电压突降是造成风机自动跳闸的主要原因。对风机电气控制技术进行改进，采取了去掉低电压跳闸保护、增设专用二次控制电源、设置瞬时断电延时自启动控制线路等措施，有效地避免了风机故障的发生，年减少经济损失66．13万元。     

基于B点磁探针膛内电枢电弧长度与速度分布测量的计算机控制系统的研究

基于B点磁探针的测量原理，建立了电磁轨道炮膛内三维等离子体电枢电弧长度和电弧运动速度测量的数学模型，通过对该模型的分析给出了用于测量膛内电枢电弧长度和运动速度分布的相应推论。开发了用于测量膛内等离子体电枢电弧长度和速度的多通道计算机控制诊断系统，并进行了相应的试验研究。     

Electrical conductivity in iodine-doped ethyl cellulose

The electrical conductivity of solution-grown ethyl cellulose (EC) films, 5–30 μm thick, has been studied in the sandwich configuration (metal–EC–metal) as a function of iodine concentration from 0.5 to 5.0 wt% ratio. The studies were conducted in the temperature range 333–383 K, while the field was varied over the range (3.0–5.5) × 10⁴V/cm. Aluminium was used as the lower electrode, while the upper electrode was of Al, Ag, Cu, Au or Sn. Certain transient effects such as a large burst of current immediately after the application of field were observed. An attempt was made to identify the nature of the current by comparing the observed dependence on electric field, electrode material and temperature with the respective characteristic features of the existing theories of electrical conduction. The results show that the electrical conduction follows Ohm's law at lower fields, while at higher fields, space-charge limited current (SCLC) was observed. It was also found that Richardson–Schottky emission was responsible, to some extent, for the transport of charge carriers in the polymer. The conductivity of the films increased on doping with iodine. The dopant molecules are considered to act as additional trapping centes and provide links between the polymer molecules in the amorphous region, thus resulting in the formation of charge transfer complexes.     

Procedures for analysis of strain transfer in the acetabular region in vitro

The failure of acetabular cups via loosening, migration or fracture is partially related to the stress distribution existing in the acetabular region. The complexity of the investigation of these stresses demands the application of a variety of model testing techniques involving combined embedded strain gauging, finite element analysis, transmission and reflective photoelasticity and crack propagation studies. The application of these procedures are described and the difficulties of obtaining representative loadings and restraints are commented upon.     

Color characteristics of Cu-Zn-Al alloys

ＣＯＬＯＲＣＨＡＲＡＣＴＥＲＩＳＴＩＣＳＯＦＣｕ－Ｚｎ－ＡｌＡＬＬＯＹＳ￣①Ｌｉ，Ｂａｏｍｉａｎ；Ｚｈａｎｇ，Ｘｉｕｈｕａ（ＳｈｅｎｙａｎｇＩｎｓｔｉｔｕｔｅｏｆＧｏｌｄＴｅｃｈｎｏｌｏｇｙ，Ｓｈｅｎｙａｎｇ１１００１５）ＣＯＬＯＲＣＨＡＲＡＣＴＥＲ...     

High‐Tech‐Cellulose‐Funktionspolymere nach dem ALCERU®‐Verfahren

Functional High‐Tech‐Cellulose materials by the ALCERU® process Cellulose is one of the eldest materials of mankind. While the use of cellulose in former times was focused on application as a more construction or as a more textile material at present time the application profile turns to a more functional material using the ALCERU® process. Shaping of pure cellulose dissolution in NMMNO permits the manufacturing of materials for upholstery, filtration or biodegradable film strips having an uniform cross section. Fibreds, which can be applied in several packaging materials, are available using different techniques for regeneration cellulose. A great field of innovative functional cellulose materials is opened up by addition of several functional additives to cellulose dissolution. In this way piezo‐electrical conductive cellulose fibres (PZT) or high‐temperature filtration membranes are to be generated if one adds special types of ceramic powders. Above all PZT green fibres are applied in more recent uses as sensors or actuators. Electrically conductive cellulose fibres or filaments, which can be also used in the textile chain, can be prepared adding conductive carbon black to a cellulose dope on the same way, too. Cellulose material having adapted conductivity to different application is available by adding an exact defined amount of carbon black to cellulose dissolution. Finally cellulose beads can be manufactured by means of varied shaping technique. The beads are showing variable particle sizes and narrow pore size distribution. These properties open up very interesting application in the field of human blood purification or chromatography.     

Structural and electrical properties of brush plated ZnTe films

Zinc telluride thin films were deposited by the brush plating technique at a potential of −0.90 V (SCE) on conducting glass and titanium substrates at different temperatures in the range 30–90 °C. The films were polycrystalline in nature with peaks corresponding to the cubic phase. Direct band gap of 2.30 eV was observed. XPS studiers indicated the formation of ZnTe. Depth profiling studies indicated a uniform distribution of Zn and Te throughout the entire thickness. EDAX measurements were made on the films and it was found that there was a slight excess of Te. The carrier concentration was found to vary from 10¹⁴–10¹⁵ cm⁻³ with increase of substrate temperature. The mobility was found to vary from 5 to 60 cm² V⁻¹ s⁻¹.     

纳秒级上升时间的高压脉冲群电源

按照IEC 61000-4-4/GB 17626.4—1998的要求，首先应用PSPICE仿真确定电路中各元件的参数值，然后基于拉普拉斯变换用MATLAB求解二阶电路验证各元件参数。在此基础上研制了一台以开关电源作为高压直流电源、以氢闸流管作为主控开关的脉冲群电源。该电源体积小、重量轻、效率高、成本低廉。试验结果表明，其输出信号符合标准要求，可用于快速瞬变脉冲群抗扰度试验。     

Synthesis and aqueous solution behaviors of sodium sulfonate‐terminated dendritic poly(ester‐amine)

Sodium sulfonate‐terminated dendritic poly(ester‐amine) (SPEA) was synthesized by sulfonation of acrylic double bond‐terminated dendritic poly(ester‐amine) (APEA) with sodium hydrogen sulfite (NaHSO₃) in mixture of diglycol and 2‐butanone under normal pressure. The structure of SPEA was characterized by IR, ¹H‐NMR, and elemental analysis. SPEA was water‐soluble. 1.0–40.0% (mass) SPEA aqueous solutions appeared as dilatant fluid. When pH value varied from 1.5 to 12.0, the viscosity of 1–5% (mass) SPEA aqueous solutions changed very small, and the electric conductivity almost kept stable within pH 3.0–10.0. The relationship between the viscosity and the concentration of SPEA water solutions was similar to that of NaCl water solutions. The surface tension of SPEA water solutions was lower than that of polyethylene glycol 2000 water solutions with the same concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008